Jump to content
IMPORTANT Registration rules Read more... ×

AnthonyCecere

Members
  • Content count

    6
  • Joined

  • Last visited

Community Reputation

1 Neutral

About AnthonyCecere

  • Birthday 08/17/1984

Profile Information

  • Gender
    Male
  • Location
    Colorado
  • Interests
    Bladesmithing
    Blacksmithing
    Darts
    Pool
    Woodworking
    Chess
    Cooking
  1. AnthonyCecere

    Trouble With Histroically Inspired Bowie Construction

    About the handle. I agree, it doesn't quite look right but by no means bad. I think it's really great work. I might consider 2 things. 1; sand down the dark area to bring out a little more white and lessen the sharp contrast. 2; Carve something into the bone in the dark area as to have it framed by the high contrasting surrounding dark part.
  2. AnthonyCecere

    Building my first forge!

    Thanks for the advice! From my research, the venturi burners need about a 7 to 1 vent. By my math, i'm good when running 1 burner but the point you made has me thinking that the vent on the back chamber should be as big if not bigger than the front when running both. I'll probably also have to do some tuning when I switch between single and double burner. I'll try the half circles, if I'm not getting the correct air flow, I'll cut them out to rectangles and just expand from there if necessary. I fear that if I start out too big, i might miss out on a nice butter zone in tuning.
  3. AnthonyCecere

    Building my first forge!

    Thanks Geoff. The thing I like about my design is, because I plan on doing this full time, I like that once the forge is heated, I can reduce the fuel to a more sustaining consistent radiant heat. And personally, I do not like the vertical forges. I'm making venturi burners. Most of the research I've found shows that about 400 cubic inches is in a good area per burner. One could go much higher but lose some fuel efficiency, I imagine.As far as the space, I do worry that it's a little wide. I might consider maybe 7x7x17 @ 833 cubic inches, but I wanted the width to be able to work multiple pieces simultaneously. Perhaps have a damascus billet going while also forging out something else, etc. I feel like the 8x8x6high chamber is symetrical, and if properly vented, with the burner centered, it will be a little work horse. The second chamber will be more or less for swords and drawing out large billets. Honestly not my thing, but I imagine good to have. I'm mostly curious about what you guys think as far as, is there any reason this couldn't be a good working forge? Is that enough insulation for .03 sheet, will it be able to reach and sustain forge welding temperatures, IS IT SAFE? Are the vent holes big enough...is it majorly flawed in any way beyond personal preference?
  4. AnthonyCecere

    Building my first forge!

    I plan on building my tempering oven out of ceramic board, electric heating elements and an electronic control board to regulate the temp. I wont be able to program it but I can baby sit and time it. The temp will be accurate and controllable. The floor is 8 inches x 17 inches. When divided into single burner mode, it will be 8 x 8 inches.6 tall with the burner centered in the middle of that space. Is the cast floor still not good?
  5. AnthonyCecere

    Building my first forge!

    So I decided to be a bladesmith. The first thing that I find to be important is having the right equipment. I wont argue that amazing works can be made with a file, but I'm lazy. Over the coming months, I'll be building my own forge, 25 ton forge press, 2x72 belt grinder, tempering oven, tool cabinet, and probably some other stuff along the way. I'm very tempted to start with the belt grinder and tempering over. I could pretty much make a ton of good knifes with just that, I imagine. But I digress, project 1; Propane Forge! I've done a ton of research and learned a few things. Things I want to run by you guys as I explain my design choices. First off, I decided that the thickness of the metal encasing the forge is less important and it wont really get too hot if properly insulated. *except around the openings. So for the body, I'm going with .03" sheet steel tac welded to a fame of corner bar. As far as the door, imagine the whole thing as a block with the last 2.5 inches cut off, reinforced if necessary, and hung to another reinforced plate with 2 hinges. I'm going with a magnet and metal rod to open it and keep it closed. I figure I'll also put a harder holding hook on there when I wont be using the door, but rather the door vents. As far as insulation, I'm going with 2 inches of high temp ceramic wool and about .5 inches of high temp refractory. The floor I'm planning on lining with fire brick (2.5 inches) and about .5 inches of casted refractory. I am going to make the total inside area right around 800-850 cubic inches. The inner chamber dimensions will be 17 inches deep, 8 inches wide, and 6 inches tall. I plan on have a removable ceramic board wall dividing the chamber in half for the 95% of the time when I'll be using only 1 burner. I'm going with 2 venturi burners running on propane. For the vents, on the door I'm planning on a half circle 6" wide and 3" tall and on the back and dividing board, half circle 3" wide and 1.5" tall. That's pretty much it. What do you guys think?
  6. Today I planned the design of my forge. I decided on a double venturi burner forge with an internal area of 800 sq inches. There will be a removable 1 inch spaces in the middle for when I only need 1 burner. I imagine that will be 95% of the time. The internal dimensions are 8" Wide x 6" High x 17" Long. The estimated total build cost with burners and everything is about 500.

    1. AnthonyCecere

      AnthonyCecere

      I'll be using 2 inches of ceramic wool on the walls and ceiling. On top of that will be high temp refractory. The floor will be high temp fire brick and casted refractory. The burners will run off of one 100lb tank with the ability to use one, the other, or both burners at controllable pressures. I will be making the venturi burners also. The exterior will be .03 sheet steel welded to a frame made of corner steel.

  7. Joining this forum because I'm building my own shop. I recently moved to house with a detached 900 sqft workshop. Most of what I'm doing for the next month is just planning. I'm not wealthy so I intend to build almost everything you can imagine building, myself.

×