Jump to content

Search the Community

Showing results for tags 'hand tools'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


  • General
    • Read before you register
    • Forum News
    • New Board Issues
  • New Work
    • Show and Tell
    • Photography
    • Video and Multimedia
    • Knives For Sale
    • Design and Critique
  • Old Work
    • History
    • Old Masters
    • Library
  • Forge Work
    • Hot Work and Bladesmithing
    • Hot Work
    • Bloomers and Buttons
    • Beginners Place
    • Pinned topics for the Beginners Place
    • Teacher Directory
    • North American Bladesmith and Blacksmith Directory
  • Forges, Tools, Equipment and Materials
    • Tools and Tool Making
  • Finishing, Tips and Tricks
    • Fit and Finish
    • Sheaths and Leatherwork
    • Carving and Applied Arts
    • Shop Safety
    • Non-Ferrous: fittings, alloys, patinas
  • Heat Treating
    • Metallurgy and other enigmas
    • Heat Treating by Alloy
  • Events
    • Events of Interest
  • Discussion
    • The Way
    • Fiery Beards
    • Books, Videos, and other Media
  • Tailgate Sales
    • Tools, Supplies and Materials
  • Hall of Fame
    • Nominations
    • Show and Tell Hall of Fame
    • WIP/Tutorial Hall of Fame
  • Pinned Topics
    • Pinned Show and Tell
    • Pinned Hot Work Topics
    • Pinned Buttons and Bloomers
    • Pinned Tools and Toolmaking
    • Pinned Fit and Finish
  • Maker's Mark Registry
    • Maker's Mark Registry
    • Marks to be Identified
  • KITH
    • KITH 2011-2020
    • KITH 2021
    • KITH 2022
    • KITH 2023

Find results in...

Find results that contain...

Date Created

  • Start


Last Updated

  • Start


Filter by number of...


  • Start





Website URL







Found 2 results

  1. Hi All, My first knife was not too good (tried to make from stainless, screwed up HT), but my second one I'm quite proud of. Made by stock removal from an old file (the one I dulled filing stainless....), using only hand tools, except for drilling the two holes in the handle. No Jigs used, mostly filing by hand (and eye) and using grindstones from my lansky-set to smooth the surfaces. HT done in purposebuilt charcoal forge from bricks, quench in sunflower oil. For my next one I hope to start with a bit of forging before I start the filing. video of het treat: 22222625_1617613648262066_7814047959703617536_n.mp4
  2. I walked into an antique store a couple days ago looking for a pocket watch for my brother. Lo and behold they had a Goodell-Pratt 2 speed breast drill for sale. I've been looking for just such a drill for a while so naturally I couldn't leave without it. I did not, however, leave with a pocket watch, funny how that happens. Here are some pics. The speed on the drill is adjusted by pulling out and turning a little knob which slides an internal component that will engage one of the gears while the other turns idly. My drill had a problem however, it wouldn't engage the smaller gear. I was really concerned something was broken so I had to take it apart to see. Although it's a simple design, I was a little puzzled about how to get it apart so hear is how I figured out how to do it: Step 1: Unscrew these 3 screws. Step 2: The crank handle and gear should slide right out. The main drive shaft (is that the right name?), with the chuck, should also pull out easily, but in my case there was a swell along the corners of the groove on the shaft that made it very difficult to remove. I was afraid to break it by pulling something out that shouldn't come out but there didn't seem to be any other way to take it apart. So I gave it a good tug and viola! It popped right out. A little 180grit sandpaper cleaned up the swell in a few seconds and it slides nicely now. Below are some pics of the gear mechanism. The center part slides up or down to engage only the gear you wish to drive the drill, thus changing the speed and power ratio. I love the simplicity of it. When I first took it apart the center piece was oriented in the opposite direction as shown above, which I believe was preventing it from engaging the lower gear. Flipping the piece and cleaning up the shaft fixed the problem and now I have a new (old) working breast drill. (This will go great with my steampunk welding goggles ) Here are a couple pics of the unusual 2-piece chuck. It will be handy for square and tapered bits, but I also bought a regular 3 prong chuck that will fit inside this one to hold those ever-so-handy small drill bits.
  • Create New...