Jump to content

Search the Community

Showing results for tags 'regulator'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


  • General
    • Read before you register
    • Forum News
    • New Board Issues
  • New Work
    • Show and Tell
    • Photography
    • Video and Multimedia
    • Knives For Sale
    • Design and Critique
  • Old Work
    • History
    • Old Masters
    • Library
  • Forge Work
    • Hot Work and Bladesmithing
    • Hot Work
    • Bloomers and Buttons
    • Beginners Place
    • Pinned topics for the Beginners Place
    • Teacher Directory
    • North American Bladesmith and Blacksmith Directory
  • Forges, Tools, Equipment and Materials
    • Tools and Tool Making
  • Finishing, Tips and Tricks
    • Fit and Finish
    • Sheaths and Leatherwork
    • Carving and Applied Arts
    • Shop Safety
    • Non-Ferrous: fittings, alloys, patinas
  • Heat Treating
    • Metallurgy and other enigmas
    • Heat Treating by Alloy
  • Events
    • Events of Interest
  • Discussion
    • The Way
    • Fiery Beards
    • Books, Videos, and other Media
  • Tailgate Sales
    • Tools, Supplies and Materials
  • Hall of Fame
    • Nominations
    • Show and Tell Hall of Fame
    • WIP/Tutorial Hall of Fame
  • Pinned Topics
    • Pinned Show and Tell
    • Pinned Hot Work Topics
    • Pinned Buttons and Bloomers
    • Pinned Tools and Toolmaking
    • Pinned Fit and Finish
  • Maker's Mark Registry
    • Maker's Mark Registry
    • Marks to be Identified
  • KITH
    • KITH 2011-2020
    • KITH 2021
    • KITH 2022
    • KITH 2023


  • Community Calendar

Find results in...

Find results that contain...

Date Created

  • Start


Last Updated

  • Start


Filter by number of...


  • Start





Website URL







Found 3 results

  1. Hello,- I'm working on putting together a forge and am looking at propane regulators. I don't know a ton about this stuff so bear with me. If I get a regulator like this, can I put a gauge down the line from it since there is no port on this particular regulator? How does one add a gauge to line? Can it simply screw into a T-Fitting of some kind? Help me shed some light on this conundrum. Thanks,
  2. First off- I understand this isn't strictly about bladesmithing... however, I was working on metal when this problem arose... and blades are also made of metal... is this even the correct board? Apologies if there is a better location. I have been asking around and haven't found a straight answer yet to my question so I figured I would put it to others that likely also use oxy-acetylene torches. So, I was heating up a large piece of steel with a rosebud tip and seem to have broken the 1/7 rule. When I turned the torch off I immediately noticed the smell: acetone. I looked closer and noticed a reddish greasy liquid bubbling at the tip. Acetone seems to have been pulled up during the high pressure heating. Given that I now have gooey acetone in the regulator and hoses. I understand this is a BAD thing. But, my QUESTION is: how bad? is my acetylene diaphragm (and hoses?) slowly being eaten away and it's just a matter of time before I blow myself up? Is there any effective and safe way to clean this stuff out or do I need to re-build the regulator / buy a new one? I've asked a few people online and to my local machinist and their answers were sort of vague. Any advice that isn't vague? Thanks in advance, Eric
  3. The attached picture is of my propane tank and the torch I have purchased. The system I am running is a forced air (hair dryer) forge. I have tested it out and it seems to work fine, I just want better efficiency so I can work longer. What I would like to know is what do i need as far as regulators go? Do I need a high pressure reg? Or a low pressure reg? I found a webpage from Don Fogg talking about the setup he recommends, using a high pressure reg at the tank and a low pressure reg with a needle valve and shut off close to the forge. Do I really need the low pressure reg? Or is it a preference thing? I'm almost positive that the torch itself is equipped with a needle valve and shut off so i don't need those. Also a general explanation of high vs low pressure as it relates to propane and forging would be nice as well (in lay terms, as some of the resources I have checked went over my head) Any and all help is appreciated!
  • Create New...