Search the Community
Showing results for tags 'Gas Forge'.
-
howdy, lately I've been thinking about building a propane forge but before I start I thought i'd better check and make sure I was on the right track. first, is a smaller forge more efficient than a larger forge? common sense would say yes but what do I know lol. originally I was planning to use an old propane tank or a 5 gallon air tank for the forge body but got to thinking they may be larger than I need right now. I have some 8" wide pipe and I think some 6" or 8" wide tubing that might be a better starting option for me. second, not having any experience with burner
- 9 replies
-
- gas forge
- gas burner
-
(and 1 more)
Tagged with:
-
Beginner's Place seemed appropriate for this. So I'm in the process of planning out my next forge. I'm not completely new at this game, I'm already made a small charcoal forge (which ended up failing) and a venturi gas forge (which works). All my tool and equipment before were mostly cheap tools or improvised, so now I'm slowly working at buying/making proper bladesmithing gear. The next on the chopping block is my forge. Now my other isn't bad, it's actually a pretty nice little forge, was even able to do some forge welding with it. The problem is that it isn't the most well-put together
- 17 replies
-
- newbie
- forced air
-
(and 1 more)
Tagged with:
-
Hello everyone, im brand new to this site so if this is a dumb question please tell me. I need a couple fire bricks for end caps for my propane forge. Unfortunately in my area (SW Florida) it is impossible to find fire brick within 150 miles. I’ve found a few recipes for refractory cement but again the only materials I can find around here are Portland cement I-II, perlite, crushed silica, hydrated lime. Has anyone experimented with this recipe and would it suffice as a temporary fix until I can build a new forge properly?
- 1 reply
-
- gas forge
- refractory
-
(and 1 more)
Tagged with:
-
I'm making my new forge and I'm thinking of using insboard as a sacrificial floor on top of 2" thick inswool. The typical hard firebricks I find that I used for the floor of my last forge aren't long enough for this one. Would insboard make a good replaceable floor, should it be coated, or is this a bunk idea entirely? Thanks for any help you can give.
-
Good evening everyone, I am getting ready to start a forge build this weekend, the body of the forge will be an 11 gallon compressed air tank ( I only chose this over the 5 gallon because I am hoping to work on some wider pieces that might not fit in the narrower body after insulating) My current plan is -a rectangular door in the rear with angle iron top and bottom so that I can slide a brick in to block the hole. -larger rectangular door on the front, also with angle iron so that I can close most of it off to allow higher temps. -I currently have 2" ceramic wool, 10 x 1/2
-
So I decided to be a bladesmith. The first thing that I find to be important is having the right equipment. I wont argue that amazing works can be made with a file, but I'm lazy. Over the coming months, I'll be building my own forge, 25 ton forge press, 2x72 belt grinder, tempering oven, tool cabinet, and probably some other stuff along the way. I'm very tempted to start with the belt grinder and tempering over. I could pretty much make a ton of good knifes with just that, I imagine. But I digress, project 1; Propane Forge! I've done a ton of research and learned a few things. Things I
-
I've recently learned from fellow bladesmiths on this forum that forced air burners are more economical than their venturi counterpart. After tearing my hair out about thinking that I'd have to buy new burners, I also learned that you can possibly put a blower onto a venturi via the large orifice on the T-pipe that the burner sucks air through. Does anyone know which blower is best, how to attach it, and if this is really possible? If it helps to have the info, I'm using two side arm burners from Zoeller Forge. Would I need a blower for each burner, or is one for the front burner enough? I hea
-
Hello Everyone, I am establishing a new shop in Toronto. One of the last things I need to do is run my propane from the bottle outside, to the forge. The propane forge will be outside in a cage, the forge will be roughly 60' away, inside. The burner is a blown burner, I got the idea from Geoff Keyes. My question is how to run the propane from the bottle to the forge, what should the propane run in (rubber or black iron pipe?). What diameter of pipe is needed? Where would pressure valves and other devices be located? Last question, I know this will vary by local but does this
- 10 replies
-
- natural gas
- propane
-
(and 1 more)
Tagged with:
-
Last weekend I made my first attempt at trying to forge weld. I've been wanting to learn for quite a while, with the intention of working my way up to welding up some billets eventually. I decided to start by trying a few chain links. Out of five links that I attempted, I may have gotten one to stick. Couldn't knock the joint apart with a hammer like the other four, so it might have actually welded, but I'm not sure. It seemed like the forge was not getting hot enough. I've read elsewhere about people forge welding billets at 5 psi with the same forge, but mine was just not getting t