Jump to content

Fuller Sanding Blocks WIP


MSchneider
 Share

Recommended Posts

I recently decided to try making some cast fuller sanding blocks and I thought I’d share how I went about it. I’m really pleased with how well they work. PVC pipe is measured in ID and lines up nicely with the wheel sizes I generally use for fullers. I made a 1.5”, 2” and 3” block using the corresponding PVC pipe sizes.

 

For the casting material I used Smooth-Cast 300. It is a 1:1 casting resin with a finished Shore hardness of 70. It is inexpensive, mixes easily and sets up quickly. I purchased it from Amazon: https://goo.gl/Wha5ga.

 

p611486794-4.jpg

 

I prepped the PVC by cutting it into 4” sections and then splitting it in half lengthwise. Here are my 3 mold forms.

 

p940275148-3.jpg

 

In order to secure a wooden block to the top, I embedded 2 stainless screws. I created a reusable card stock template for placing the screws so that the spacing would be the same on all the blocks.

 

p793788377-3.jpg

 

To make the ends of the molds I first put on a layer of masking tape and then strengthened it with a little duct tape. I then sprayed the inside of the mold with some WD40 to act as a release agent.

 

p1036982639-3.jpg

 

This is the mold ready to pour. It is filled thought the opening left in the middle of the template.

 

p1018098805-3.jpg

 

The filled mold curing.

 

p885284946-3.jpg

 

…and after cured.

 

p830670524-3.jpg

 

I took the cured blocks and ground the sides flat, cleaned the ends up a bit, added a little texture to the sanding face and trimmed the mounting lugs.

 

p553220131-3.jpg

 

p997245890-3.jpg

 

I then used some epoxy to mount the wooden top to the block and they were ready for use. Here are the well used 2” and 3” blocks.

 

p849501706-3.jpg

 

 

Thanks,
Mark

Link to comment
Share on other sites

very clever!

www.hoyfamily.net

Isa 54:16 Behold, I have created the smith that bloweth the coals in the fire, and that bringeth forth an instrument for his work; and I have created the waster to destroy.Lu 22:36 Then said he unto them, But now, he that hath a purse, let him take it, and likewise his scrip: and he that hath no sword, let him sell his garment, and buy one. Mr 8:36 For what shall it profit a man, if he shall gain the whole world, and lose his own soul?
Link to comment
Share on other sites

Nice!

-----------------------------------------------

"It is not the critic who counts; not the man who points out how the strong man stumbles, or where the doer of deeds could have done them better. The credit belongs to the man who is actually in the arena, whose face is marred by dust and sweat and blood, who strives valiantly; who errs and comes short again and again; because there is not effort without error and shortcomings; but who does actually strive to do the deed; who knows the great enthusiasm, the great devotion, who spends himself in a worthy cause, who at the best knows in the end the triumph of high achievement and who at the worst, if he fails, at least he fails while daring greatly." -- Theodore Roosevelt

http://stephensforge.com

Link to comment
Share on other sites

  • 6 months later...

homemadetools guy here, not a spammer (PROOF: 400+ forums that know us)

Just a note that we featured Mschneider's build in our newsletter, fully credited and properly linked of course. We're admirers of this forum, we have 52 of your homemade tools indexed so far, each one fully credited to its builder: 52 homemade tools from BladesmithsForum.com.

 

I hope we've been able to bring you lots of visitors. Cheers.

Edited by JonathanR
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share

×
×
  • Create New...