Jump to content

Recommended Posts

Tim, when I said bomb proof, I meant a solid, can handle anything thrown at it, strong design.... it was meant as a compliment.  I haven't tried to tackle an integral yet, so my hat off to you!

  • Like 1
Link to post
Share on other sites
2 hours ago, MikeDT said:

Tim, when I said bomb proof, I meant a solid, can handle anything thrown at it, strong design.... it was meant as a compliment.  I haven't tried to tackle an integral yet, so my hat off to you!

Thanks Mike

Oh, someday..   they will be works of art.

Link to post
Share on other sites

new cutter done, hand forged from 01 tool steel. Scales HSS blended in & contoured smooth. 

13 1/2" overall

7 3/4" cutting edge

3/16" spine convex beveled to a razor blade 

2 1/2" blade 

not going full polish on this, just keeping the hours down.

have two more to finish up one similar the other not as much.

IMG_0941.JPG

Edited by Tim Jackson
Link to post
Share on other sites
On 9/10/2018 at 10:35 PM, SteveShimanek said:

You have a unique style for a beginning smith; that is very nice and I can see you building a following!

Thank you so much for those sentiments Steve. I have recently worked for free with two blacksmiths to get some experience. Wanting to find a bladesmith in the Tucson area to learn from. 

Edited by Tim Jackson
misspelled Tucson :0
Link to post
Share on other sites

Diagonal cross pein 

I can work with wood, just do not like to. Fills the shop up with dust (everywhere) have to change respirator filters, etc, etc..

Oh, handle is hickory, just used my 5" Metabo hand grinder to fit & grrrind the wood down. Then touch up on the belt sander. Flame hardened & slathered on some boiled linseed oil.

 

Can mods place this glowing head as avatar please?

IMG_0800.JPG

IMG_0801.JPG

IMG_0802.JPG

IMG_0803.JPG

IMG_0804.JPG

IMG_0805.JPG

Edited by Tim Jackson
asking mods if would make profile pic
Link to post
Share on other sites

took some photos while forging today, from about 80% completed  made two chef knives started from 1" x 7" round    01 tool steel     2.54cm  x  17.78cm

Full integral,  Brute de Forge update this when they get completely finished.

any thoughts? 

 

 

IMG_0978.JPG

IMG_0979.JPG

Edited by Tim Jackson
added metric equivalent measurements
Link to post
Share on other sites
On 9/22/2018 at 10:50 PM, Tim Jackson said:

any thoughts

More just wondering how you get to full integral from there. Do you need to upset the tang width-wise?

Link to post
Share on other sites
3 hours ago, Charles du Preez said:

More just wondering how you get to full integral from there. Do you need to upset the tang width-wise?

As in a bolster? Perhaps my terminology is off? don't know. 

Just planned on hammering in the transition, then grinding the blade per usual. 

Link to post
Share on other sites

Chef knife 01 tool steel

my take on  "Brute de Forge" from a 1" - 2.54 cm round bar. 

14 1/4" 36.195cm overall
blade 7 1/2" 19.05cm .. 2" 5.08cm at the heal. taper to 1 3/4" 4.445cm at tip 
blade is 1/16" 1.5875mm thick
handle is a generous 6 1/2" 16.51cm long, 1" 2.54cm wide (average) 
 

hope my metric conversions are precise

completed

 

 

IMG_0819.JPG

IMG_0978.JPG

IMG_0979.JPG

IMG_0989.JPG

IMG_0990.JPG

IMG_0996.JPG

IMG_1002.JPG

Edited by Tim Jackson
Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...