Jump to content

Wrought iron axe


Jeremy Blohm

Recommended Posts

18 minutes ago, Will Wilcox said:

Some people just dont appreciate handcrafted stuff I guess

I appreciate handcrafted stuff, but only if it's well made (most is not) and if it's some thing of interest to me.  The fact that it's handcrafted is the lowest of the factors I use to buy something.

Link to comment
Share on other sites

I'm going to try my absolute best and hopefully I can appreciate and use it. I should say that I have over $15000 is equipment and I haven't sold a single piece that I've made. There was a time when money was tight and I was going to try my hand at making a dollar and I never ended up doing it and the tight budgeting came to an end and now I'm working on getting to where I feel comfortable selling my stuff. So far I have just given it all away or kept a few things to use for myself. 

Link to comment
Share on other sites

Pay particular attention to steps 26 and 27 in Gerald's guide.  That's where I seem to be falling apart on my latest attempts. 

 

18 minutes ago, Jeremy Blohm said:

I'm going to try my absolute best and hopefully I can appreciate and use it.

I'm in the same boat with that.  To make a wall hanger is nice.  My goal with the wrapped axes I've tried was always to make something use able. The ones that I have together are just the wrong shape to accomplish anything. 

 

It does sort of stink that I've been trying to wrap one every forge chance I get.  Then I watched a friend of mine make a nice hatchet from a brick hammer in about the same amount of time for me to mess up one wrapped axe.

Link to comment
Share on other sites

I've tried 3 wrapped eye axes with mild steel and only one turned out ok and my father-in-law uses it daily at his wood stove. The only thing I didnt like was I didn't get the height in the cheeks I wanted.

 

Here is a few pictures of the grain after quick etch.B)

 

 

Resized_20191114_101853.jpeg

Resized_20191114_101843.jpeg

Resized_20191114_101830.jpeg

Link to comment
Share on other sites

1 hour ago, Daniel W said:

Pay particular attention to steps 26 and 27 in Gerald's guide.

Don't know if you did or not, but make sure the inside corners are soft on the bow tie.  Soft corners will curve over, sharp corners will fold over sharp and than might start to crack.

Link to comment
Share on other sites

Nat bad. I'm only 20 minutes past where I wanted to be. I wanted to get to this point by noon but a guy and his wife slid off the road trying to make the corner and I had to pull them out of the ditch and that set me back 30 minutes or so. :lol:

  • Like 1
Link to comment
Share on other sites

, Thank you!

 

I wanted to refine it a little more but it was getting to be about 10 pm and the wifey and kids were yelling at me about the anvil ringing and they wanted to go to bed <_<

Link to comment
Share on other sites

Yup, whut them dudes said man ....................;)

  • Thanks 1

If ya can't be good don't git caught  !!                                        People who say stuff can't be done need to

                                                                                                        git the hell outta the way of people who do stuff   !!!

Show me a man who is called an expert by his peers         

And I will show you a good man to listen to ......

Show me a man who calls himself an expert

and I will show you an egotistical asshole...............!!

 

                             

Link to comment
Share on other sites

Thank you gentlemen!!!!

 

I'm going to make a better drift to get rid of the "hollowness?" In the eye area. I had a drift I had already made that I tried to get to work and it did for the most part but I want them a little better. Part if the reason that hollow is there, is because one of the peaks didn't get drawn out quite as much as the other three so I worked it a bit with the drift in. I'm going to trim the top and bottom of the blade to make it a bit more like the one in the article.

Link to comment
Share on other sites

This is what I'm thinking. Or should I forge it all to shape? I just fear it will end up too long!

20191116_111001.jpg

Part three finally uploaded!!!

 

 

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...