Jump to content

My contribution 2021 KITH


Recommended Posts

Greetings!

This might be long winded, I don’t post too often, although I check in 7’al times a day.

Late last year, waiting for surgery in January for torn rotator and bicep, I couldn’t do much. I had a couple of ends left over from a W2 bar and  Cru Forge V, both approx. 3” long. I cut these lengthwise in half, thinking maybe I could be frugal enough, to make something and buy more material. I made 2 EDC Knives from the CRU, and a matching pair for my grand boys in the W2. (Pictures will follow) 

Ironically these measured 1/2 cubic inch, so when we decided on 1 cube inch I figure it would be fun. I like doing KITH and try to participate every year.

Figured everyone would be playing with Pattern Welded, so I sandwiched 52100 core, to 15n20 to, mild steel wrap outside.

However, in order to get the dimensions for 1” cubed, my starting blocks was too thick and wide. 

Its welded perfectly, and first photo is starting the process of going thinner and longer.

 

 

22582A3E-E17A-4D97-865E-1B76895B9553.jpeg

99419DD5-787E-4778-BBA7-F32BA4F51168.jpeg

Link to post
Share on other sites

Then.....not so simply hammering this billet into appropriate dimensions needed for 1” cube.

The length grew 3” to 4”, then 5”, 6”, 7”, 8”

I haven’t encountered something so difficult in a long time. I peened, used the horn, anvil edge, guillotine, all while all working temps where around 2000F. I wound up working on this as I forged other stuff over time.

9529884D-13E4-43E6-910B-9D80F33643D1.jpeg

71DB959F-0845-4CA4-AC37-414B3B564E06.jpeg

1B0F6CF6-362F-47A8-9F68-0E460193691F.jpeg

92894E5B-4F3C-4387-995F-F4C6F86F0685.jpeg

48D8AAAC-B43C-4A64-84D7-255E3F2CB836.jpeg

F1759663-7A91-4191-ABCA-C5FEAEE8D40F.jpeg

93A0796A-965D-462F-8088-A4F23A86A377.jpeg

Finally I had something to meet the specs.

721B1BE1-E8A0-42BE-83CA-A01530210136.jpeg

426755CC-9F81-4792-B0B3-982B5F9F3D80.jpeg

DCE55F45-A9C9-42DB-8FA5-1D121E777328.jpeg

Link to post
Share on other sites

On knives this size and with I like forming the tang first allowing approximately 25-33% of the starting length for the tang. Once the tang is formed well enough, I have something to hold onto. I’ll move back and forth between the tang and blade drawing each out in length, taper, width and shape.

 

2B42786F-EAFA-4A33-B671-2753787E3C15.jpeg

38F53E23-8B65-4E1D-BD69-77CA0A7385A5.jpeg

54436914-21F0-4D96-9EB2-719B17874778.jpeg

  • Like 1
Link to post
Share on other sites

When I’ve gone as far as I can in shaping by hammer, grinder comes next. I’ll use a plain bench grinder, to rough in the shoulders, blade shape and grind through the scale enough to begin some bevel. 

(Unfortunately, I missed these photos but I’ll substitute a few from the 1/2” cubed Knives)

5100BFAA-DBFD-4F76-8685-EAE40F727912.jpeg

C2EF0E78-3715-42EB-AE40-827151BECADA.jpeg

081171B5-A268-4809-859E-2B06F78173EE.jpeg

AB95B505-EF90-4F7E-BB26-11C4EAA848A6.jpeg

  • Like 2
Link to post
Share on other sites

My hopes where that in all the hammering I kept the layers uniform as possible. I decided to add drill holes on each side to add more topography after etching. The grinding process and continued etchings would meet together and offer more waviness. (Almost!) 

The layers stayed fairly even, there was some drift and I had to keep the blade symmetrical. What I didn’t like was the after etch color of the mild steel and I took the finish up to 800 grit before the first real etch. I repeated this sanding/etching over 12 times until I got a color with topographical highlight I wanted.

I do like etched blades showing wrought, layers, etc. but I am not a big fan of darkened blades, whether etched or coffee. I have used bluing before satisfactorily and I always boil in distilled water for a minimum of 10 minutes to keep the oxides/color.

4CF8CFCD-244A-403E-90B5-C42341E8EC00.jpeg

1502556F-7D2B-4A86-81E6-9755E0CA6386.jpeg

D190349B-E77F-49F6-970B-8861D2DF6E63.jpeg

1FECD027-E90B-451D-82D2-A98D5C6404E1.jpeg

557348E1-E82A-4608-AAE7-B5C758E5F2F6.jpeg

10F42584-2D4A-4C25-9372-092DA04C6B27.jpeg

91D1E1FA-2458-4268-A963-E37CD2FC68FE.jpeg

  • Like 1
Link to post
Share on other sites

After the blade was boiled I waxed it and it really improved the finish. 

I began the handle idea I wanted. First forming a block into the shape which fit the blade, I shaped the handle to the final dimensions I needed. I then made the NS guard and pommel, which I left lightly sanded.

I used what I call “redneck urushi” applied to the handle which also allowed a little museum finish at the edges, set the blade with west systems 24 hour epoxy.

These are the final photos and I am pleased with the final product. I expect over time the handle will abrade some but I have handled this a lot and it shows no sign of texture loss.

I added a simple patch sheath with a loose fit. 

I hope this WIP isn’t too boring. I am pleased to answer any questions anybody may have, comments of course are welcome 

 

 

4BFE0689-C637-41CF-912E-E810340DE9DA.jpeg

2FB1BBB9-05E6-41E9-9032-FE00EC3DA8BF.jpeg

3F14B7CE-DD9E-4DAD-8062-17D3149C2E6B.jpeg

AD17E56D-559E-4E5B-92A6-269010BAAC18.jpeg

330142B9-2AAE-467D-9E9A-9F42B10715A8.jpeg

86EB5BC4-9338-4250-83C0-0DCFB7373BFA.jpeg

B75BEABB-3535-4D59-A923-0CC60EA1F931.jpeg

  • Like 7
Link to post
Share on other sites

Nice WIP.  I second the request for more info on the handle, if you please.

Link to post
Share on other sites

Nice comments and thanks to all.

I use West Systems GFlex epoxy 50/50 ratio. Colored with a dab of black acrylic artist paint. Brush it on or use a light piece of thin wood with some flex. It will smooth out quickly and it doesn’t run for me. The sprinkle with ground tea leaves gently being sure to get complete coverage, lightly patting if needed. This is 24 hour epoxy but I like to get it started in the hot sun, checking a few time to be sure nothing has moved. It gets rigid enough to handle in a few hours.

I painted this black with Rustoleum gloss. (Yeah I know not at all professional but I don’t have an airsprayer). I inserted a dowel and spun this slowly while spraying. It doesn’t take much.

Put it up inside in an air conditioned environment and forget about it for a few days, maybe more. Got the idea of black paint from Aiden on lasts year KITH.

Done this before in the past, below are some photos, 2 sold quite well, the 3rd I haven’t offered up yet.

Well that’s the secret recipe!;)

 

Gary LT

836AB205-6303-46F7-80F6-C6788B173ED5.jpeg

4C6A69C4-EB91-496E-9114-9651FC01977A.jpeg

C86CB04E-A545-4C2A-A6BD-2F72BB140648.jpeg

  • Like 2
  • Thanks 1
Link to post
Share on other sites

Thank you Brian.

I’m not really adept at doing WIP, reckon the only way to improve is do more.

Gary LT

Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...