Jono Pukallus Posted October 28 Posted October 28 Hi everyone, I'm looking to try a few of the more basic folding knife styles and I'm checking some pivot and lock position geometry for a frame or liner lock (haven't decided materials yet so it could be one or the other). I'm looking at putting a stop pin just behind the top of the blade (see below) and I'm wondering: Are there any pitfalls in using the choil as the reception point for the stop pin? Or am I overthinking it and this is what you're supposed to do? Any advice is greatly appreciated! Cheers, Jono. 1
Jono Pukallus Posted October 28 Author Posted October 28 Actually, looking more closely at my geometry and where I expect the handle to cover, I will have to extend the blade, move the pivot back a little and have this notch separate to the choil, otherwise the back of the blade will stick out when it is closed. I might also play with moving the locking pin forward and closer to the pivot centre. Thoughts?
Dick Sexstone Posted November 1 Posted November 1 You have already figured out the handle will need to extend to reach the choil or the choil will need to move ... it is a game of balance .....take away from one side and that adds to the other side.... besides deciding what kind of lock to use there is the consideration of how long the blade is in proportion to the handle.... the closer the blade length gets to the handle length the you run up against the problem of the blade sticking out the end .... As you pointed out...... the shape of the end of the handle can be changed to accommodate the blade length . As you show in your drawing ... what kind of lock and how it work affects what your over all look of the blade will be ... "There are rules" and so which one is more important ? the look of the knife or the lock mechanism it uses? or both? you have already be wrestling with this as per you question ..... it can become very complicated for something so simple eh? I am more oriented to visual than to solving a locking mechanism and so the look of the knife is most important to me and I wanted the blade to be close to the handle length so my solution to this was to add a tab to the spring to enclose the end of the blade and also as the way to open the spring ... I made lock backs with traditional notch ..... and my handles were solid damascus so I did not want liners ...... but with linnerlock you could add a tab to a spacer at the end of the handle instead of running the liner all the way to the end .... like the Paul Simon song says..... "There must be fifty ways to leave your lover" there are lots of ideas amongst this forum ...I hope some others will chime in...
Jono Pukallus Posted November 1 Author Posted November 1 Thanks Dick! Yeah, it seems more and more complicated the more I think about it! I've already reworked the locking pin location, and made templates for every part, and changed the blade height/depth, and re-drawn all the templates! And I'm still thinking through further possible changes! This is where I'm at right now, but now I'm wondering if the opening to press the liner will be big enough for a nail nick or thumb stud to fit. I'm also considering mirroring the lock pin position to the same angle in front of the pivot so I could add an opening lever (don't know if there's a technical term for this one?) to the base of the blade, which would then hide in the finger guard section when it is open. All in all, it's looking like I'll be making many knives, to try all the options!
Jono Pukallus Posted November 2 Author Posted November 2 Welp, I switched the lock pin position and tried the "opening lever". Because I had a spare minute at work, I cut out some test pieces in 3mm acrylic with our laser cutter and did a quick and dirty assembly. The thicknesses are not accurate to my intended materials, but all other dimensions are I even managed to put a spring bend in the liner to test things out, but unfortunately, I forgot to allow for the thickness of the laser cut so there is a bit of play and rattle in the open position. Just an excuse to make another one! 1
Brian Dougherty Posted November 3 Posted November 3 Looks like a concept proven. I haven't tried to design one of these yet, so I'm watching with interest. -Brian
Alan Longmire Posted November 3 Posted November 3 Looks good to me! Here in the states the technical term for the little thumb stub is "flipper" or "flippy." Or plain old thumb stud, but that's boring, eh? 1
Dick Sexstone Posted November 3 Posted November 3 Congrats, you are doing exactly the correct move Jono ..... actually making one ...... I think that is the best way of all to work out your ideas.... it's easier to observe the pros and cons in 3D than in your imagination..... even if you have a drawing in front of you.... I think drawing is a very important step in the process to work out ideas thou That's really cool you are allowed use the machines at work in a spare moment ..... 1
Jono Pukallus Posted November 4 Author Posted November 4 Thanks, Dick. Yes, I've certainly already learned a lot in terms of filing in the lock and making sure I leave enough extra material there to tune it. As for the machines, I teach Design, Engineering and Construction (Construction is a cross between U.S. Shop class and an introductory trade course) at a high school so our machines are not in constant use. A personal project every now and then (within reason!) is encouraged, if we haven't used a particular machine for a while, to "keep our hand in". But yes, very cool!
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now